الدفع نوع: | T/T |
---|---|
Incoterm: | FOB,EXW |
أدني كمية الطلب: | 1 Bag/Bags |
نموذج: NM-AA00E,NM-AA00A
تفاصيل التعبئة والتغليف: فراغ التعبئة في الحالات خشبية
علامة تجارية: باناسونيك
نقل: Ocean
مكان المنشأ: اليابان
ميناء: Hong Kong
المميزات
1. مغذيات المكون الطولي تزيد من قدرة نقل المغذية للتشغيل المتواصل.
2. نظام النقل المغذي المنقسم 2.AVK2 يزيد بشكل كبير من معدل التشغيل.
3. هذا عبارة عن آلة إدخال متغير ، والتي ما زالت تحتفظ بنظام الوصول العشوائي للعلامة التجارية لسلسلة Panasert.
لذلك ، لا يلزم وجود جهاز تسجيل تسلسلي ، ويمكن إعادة الإدماج على الفور باستخدام مفتاح واحد عندما
حدث خطأ في الإدراج.
وظيفة تصحيح 4.Self تدرك الإدراج عالية الجودة و insertionrate عالية.
5. يوفر الجهاز إرشادات التشغيل على شاشة LCD الملونة ، مما يتيح التشغيل التفاعلي.
6. المعلومات المطلوبة من قبل المشغل أو لإدارة الإنتاج (errormessage ، معلومات إدارة الإنتاج ، الخ)
يمكن عرضها على الشاشة ويمكن طباعتها.
7. يمكن الجمع بين AVK و finked مع آلات Panasert الأخرى.
مواصفات الجهاز
Applicable Electronic Parts |
Taped axial lead parts (carbon resistor, cylindrical ceramic capacitor, solid resistor, diode and taping jumper wire) Jumper wire (optional) Refer to 'Insertion Part Specifications' in this section for part dimensions. |
||
No. of Part Inputs |
1. Taping width 26 mm •120 inputs (60 + 60) + Reel type jumper wire (optional) 2. Taping width 52 mm (Pack width: Max. 80) •120 inputs (60 + 60) + Reel type jumper wire (optional) 3. Taping width 26 mm and 52 mm can be used. |
||
Part Packaging | Flat pack | ||
Insertion Angle | 4 angles (X, Y, -X, -Y) | ||
Insertion Tact Time |
Max. tact time: 0.15 s/point Max. tact time conditions according to part type and insertion angle
|
||
Applicable part Insertion angle |
Axial lead part | Jumper wire | |
X direction (0°) | 0.18 sec/point | 0.15 sec/point | |
Y direction (90°) | 0.15 sec/point | 0.22 sec/point | |
-X direction (180°) | 0.30 sec/point | - | |
-Y direction (270°) | 0.27 sec/point | - | |
Other conditions for max. tact time •Feeder carriage (both 26 and 52 mm component feeders) fixed •XY table movement: Max. 30mm for both X and Y (However,within 15mm for both X and Y when there are parts above 3mm high on the PC board. ) |
|||
Pitch Switchover within the Tact |
5 mm within the tact (0.15 sec/part) | ||
Direction of PC Board Flow | Right to left | ||
PC Board Replacement Time | Approx. 2 sec | ||
Applicable PC Board Dimensions | Max. 508x381 mm Min. 50x50 mm | ||
Insertion Area | Max. 508x371 mm Min. 50x40 mm | ||
Insertion Pitch |
5 to 26 mm (Can be set freely by 0.01 mm increments.) 5 to 26 mm for jumper wire (optional) |
||
Insertion Height |
Insertion height programmable according to the part diameter and lead diameter |
||
Part Fixing System | Cut and Clinch system (piezoelectric detection system) | ||
Clinching Angle | 15° to 30° inner clinching | ||
Clinching Length |
1.2 to 1.8 mm![]() Note:The above numerical range indicates the variation which arise due to difference in the shape or material of insertion part leadsand the diameter of holes of PC Boards. |
اشترك في النشرة الإلكترونية:
الحصول على التحديثات، خصومات وعروض خاصة وجوائز كبيرة!