الدفع نوع: | T/T |
---|---|
Incoterm: | FOB,CIF,EXW |
أدني كمية الطلب: | 1 Bag/Bags |
موعد التسليم: | 7 أيام |
نموذج: NM-EJA2A, NM-EJ3A
تفاصيل التعبئة والتغليف: فراغ التعبئة في الحالات خشبية
علامة تجارية: باناسونيك
نقل: Ocean
مكان المنشأ: اليابان
ميناء: Hong Kong
إن AV131 عبارة عن آلة إدخال مكون محوري من VCD قادرة على إدخال عالي السرعة في وقت براعة يبلغ 0.12 ثانية / مكون ، مما يوفر كفاءة اقتصادية عالية. مع تبني مغذيات رأسية تتيح مدخلات متعددة (120 مدخل) واثنين من امدادات منفصلة الوحدات التي تعمل على تحسين معدل التشغيل ، تعد AV131 بالمساهمة بشكل كبير في التشغيل المستمر بدون طيار . أيضا ، تتيح وظيفة إدخال سلك الطائر المتاحة اختياريا إدخال الأسلاك الطائر دون تحتاج إلى تسجيل ، والذي لا يزيل النفايات فحسب ، بل يحقق أيضًا إنتاجًا عالي الكفاءة ومرن.
المميزات
زيادة الإنتاجية
الإدراج براعة الوقت
إدخال عالي السرعة عند 0.12 ثانية / مكون يحسن الإنتاجية بشكل كبير.
XY عالية السرعة الجدول
يوفر تصميم خفيف الوزن وجامد للغاية
ارتفاع XY الجدول السرعة.
الإدراج براعة الوقت لأربعة اتجاهات
(0 ، 90 ، 180 و 270 درجة)
وحدة الإدراج المدمجة وخفيفة الوزن والقيادة المباشرة
نظام اعتماد محرك رمح جوفاء تقدم عالية السرعة
الإدراج أثناء وحدة الإدراج تدور.
وحدتا إمداد منفصلتين للوحدات (NM-EJA3A)
وحدة إمداد الأجزاء المفصولة إلى جدولين تسمح بتحديد وضع تشغيل التزويد وفقًا لـ
احتياجات الإنتاج ، وبالتالي تحسين معدل التشغيل. (5 طرق متوفرة.)
نظام الوصول العشوائي
يسمح نظام الوصول العشوائي باستعادة أخطاء الإدراج بسرعة من خلال تشغيل الأزرار فقط.
موثوقية أعلى
حياة أطول الأجزاء المستهلكة
عكسها القاطع الشريط و
قطع الرصاص العكسي (الجانب الثابت)
تقدم حياة أطول من هذه
أجزاء الاستهلاكية.
دليل الإدراج و انتهازي
مصنوعة من مواد كربيد أيضا
ضمان حياة أطول منهم.
دائرية قوس مسطح كابل
يوفر الرأس ووحدة دوران السندان التي تتبنى الكبل المسطح الدائري المستدير عمرًا أطول لتوصيلات الأسلاك
القسم المنقول.
توسيط وظيفة
وظيفة توسيط لتصحيح المكونات خارج توسيطها على الشريط تمنع التداخل
بين المكونات و انتهازي الإدراج ، وبالتالي تحقيق الإدراج موثوق للغاية.
المثبط نوع الشريط القاطع وحدة
تقطيع قواطع الشريط المزودة بمخمد يبلغ 2.5 ملم من السكتة الدماغية (5 مم في الكل) تقليل الأضرار المحتملة على
قواطع في حال تم اكتشاف المادة الغريبة فيها.
المنطقة الكاملة وظيفة التصحيح الذاتي كميزة قياسية
يتعرف على كل من الفتحتين في موضع الإدراج لإجراء تصحيح موضعي مثالي للاستقرار
إدراج.
بالإضافة إلى ذلك ، يتم أيضًا تمكين تصحيحات الخطأ الدوراني ودرجة الإدراج للإدخال بدقة عالية
تحديد المواقع (XY و θ و W) ، مما يوفر معدل إدخال أعلى.
Power supply |
• Rated voltage 3-phase 200 / 220 / 380 / 400 / 420 / 480 V selectable • Frequency 50 / 60Hz • Rated capacity Approx. 4kVA |
||
Air supply |
• Service air pressure 0.5 MPa • Air consumption Approx. 150 L/min. (A.N.R) Note: Quick coupler attached (SMC KK13P-03M, KK13S-03F). |
||
Dimensions |
• NM-EJA3A W4070 × D1910 × H1610 mm (Not including signal tower) • NM-EJA2A W2810 × D1910 × H1610 mm (Not including signal tower) |
||
Mass |
• NM-EJA3A Approx. 2,520 kg (main body only) • NM-EJA2A Approx. 1,750 kg (main body only) |
||
Environmental requirements |
• Ambient temperature 20°C ± 10°C • Humidity 25 ~ 75%RH (with no condensation) • Height above sea level 1,000 m or below |
||
Transport and storage |
• Ambient temperature -20 ~ 60°C • Humidity 75%RH or less (with no condensation) |
||
Operating controls |
• Interactive operation via color LCD touch screen (Front and Rear: Standard equipment) English/Japanese/Chinese selectable with a single button Recognition screen (displays the recognized board image on a superimposed window) Hierarchical menu (Operator/Engineer) • I /O functions 3.5-inch FDD and SDD (standard equipment) • Communication RS-232C |
||
Coating color | • Standard color White: W-13 (G50) | ||
Insertion tact time |
• Max. tact time: 0.12 s/point Max. tact time conditions by component type and insertion direction |
||
Applicable component Insertion direction |
Axial lead component |
Jumper wire | |
X (0°) | 0.15 s/point | 0.12 s/point | |
Y (90°) | 0.12 s/point | 0.15 s/point | |
-X (180°) | 0.15 s/point | - | |
-Y (270°) | 0.24 s/point | - | |
Other conditions for max. tact time (0.12 s/point) • X-Y table movement Within 35 mm for X and 39.5 mm for Y (When interlock 2 is selected) (However, within 30 mm for X and 34 mm for Y when there are components above 3 mm high on the PCB. (When interlock 1 is selected)) • Feeder movement None (When the feeder moves by 1 pitch, the tact time will be 0.14 s/point.) |
|||
Pitch changeover | • 5.3 mm within the tact time (0.12 s/point) | ||
Applicable components |
• Taped axial lead components (carbon resistor, cylindrical ceramic capacitor, solid resistor, diode and taped jumper wire) • Jumper wire (optional) Refer to `Insertion Component Specifications` in this section for component dimensions. |
||
Component packaging | • Flat pack | ||
PCB replacement time | • Approx. 2 s (Ambient temperature: 20°C) | ||
Applicable PCB |
• Dimensions Min. 50 × 50 mm to Max. 508 × 381 mm Width-to-length ratio: Width should be equal to or less than length. Consult us for boards having width longer than length. • Allowable insertion area Min. 50 × 40 mm to Max. 508 × 371 mm • Thickness 1.6 ± 0.15 mm (for standard specification) *1 Although boards of thicknesses from 0.6 mm (min.) to 2.0 mm (max.) are applicable, changes to the transfer rail (option) are required if outside the above standard range. *2 Even if the board thickness is within the above range, clinched angle of the inserted lead or lead length may vary, or board transfer error may occur depending on the shapes of board or insertion holes. So it is recommended to perform an advance evaluation. • Mass Max. 1 kg per board including inserted components. • Flow direction Right to left (Standard) or Left to right (option) • Board positioning method Pin positioning (Standard, without positioning in the Y direction), Edge positioning (Option, with positioning in the Y direction) * Contact us for the board positioning in the Y direction. |
||
Insertion pitch |
• 5 ~ 26 mm (can be set in 0.01 mm increments) (Jumper wire: 5 to 26 mm (Option)) |
||
Insertion direction | • 4 directions (X, Y, -X and -Y) | ||
Anvil | • Cutting & Clinch type system (Piezoelectric detection system | ||
No. of component inputs |
NM-EJA3A 1. Taping width: 26 mm 120 inputs (60 + 60) + drum type jumper wire (Option) 2. Taping width 52mm (Pack width Max. 80) 120 inputs (60 + 60) + drum type jumper wire (Option) 3. Mixed loading of 26 mm and 52 mm tapes is available. NM-EJA2A 1. Taping width 26 mm 60 inputs + drum type jumper wire (Option) 2. Taping width 52 mm (Pack width Max. 80) 60 inputs + drum type jumper wire (Option) 3. Mixed loading of 26 mm and 52 mm tapes is available. |
||
Insertion height |
• Insertion height programmable according to the component diameter and lead diameter. |
||
Clinching angle | • 15°to 30° inner clinching | ||
Clinching length |
• 1.5 ± 0.3 mm (Reference size: 1.5 mm)*
differences in the diameter or material of inserted component leads and in the diameter of holes of PCBs. *When changing the clinching length (changing reference size), the anvil unit parts need to be replaced. (Individually supported) =REMARKS= 1. A clinch mark will be left after cutting or clinching. The shape of clinch mark varies with the lead diameter or material of the inserted component. 2. Clinched component will be tilted a maximum of ±10° in the horizontal direction due to the hole diameter of PCB or accuracy of hole position.
|
||
تقع Shenzhen Keith Electronic Equipment Co.، Ltd. في Baoan District ، Shenzhen. وهي مورد لأجهزة AI و SMT وقطع الغيار والمواد الاستهلاكية والمواد الاستهلاكية الإضافية في الصين. على مر السنين ، قدمنا معدات وقطع غيار متطورة عملائنا لضمان خدمة عالية الجودة ، وبالنسبة لسوق التصدير ، نحن نخطط لتطوير أوروبا وأمريكا الشمالية وأمريكا الجنوبية وجنوب شرق آسيا والهند وحيثما تحتاج قطع غيار المعدات SMT.
فلسفة العمل: التعاون ، الفوز ، الابتكار ، المساعدة المتبادلة
لقد تم التمسك بمفهوم إدارة العلامة التجارية المتمثل في "التركيز على جودة المنتج واحتياجات العملاء" ، من خلال تنفيذ الابتكار المفتوح وإدارة التشغيل الممتازة وتنمية الموارد البشرية وغيرها من الاستراتيجيات ، لبناء القدرة التنافسية الأساسية للشركة بشكل شامل ، وخلق العملاء والقيم الاجتماعية ، وكسب الثناء بالإجماع من عدد كبير من العملاء والمجتمع.
المنتجات الرئيسية:
Panasonic Insertion Machine، Panasonic Insertion Machine، Panasonic Placement Machine، Panasonic Placement Machine Parts، Panasonic Feeder & Feeder Parts، Feeder Trolley، SMT Cutter وما إلى ذلك. تعاونكم!
اشترك في النشرة الإلكترونية:
الحصول على التحديثات، خصومات وعروض خاصة وجوائز كبيرة!